Go back to home

Pinto Fuel Pump Spacer

Author
Post
Essentials Only Full Version
Jaycees
Aficionado
  • Total Posts : 400
  • Scores: 7
  • Reward points: 4432
  • Joined: 2011/08/01 11:02:49
  • Location: Windsor nsw Australia
  • Status: offline
2015/09/29 18:06:44 (permalink)
0

Pinto Fuel Pump Spacer

Hi,
When I see pinto fuel pumps for sale, there is never the spacer with it,
all the pinto motors I have seen have the spacer, so I assume it is necessary , any advise ?
It is like a plastic looking cardboard , can these be bought and where?
thanks Jim
#1


7 Replies Related Threads
    NQRS
    Deity
    • Total Posts : 897
    • Scores: 58
    • Reward points: 6931
    • Joined: 2011/08/01 11:02:49
    • Location: Townsville QLD Australia
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/03 23:40:31 (permalink)
    +1 (1)
    As usual on Ebay, UK.  http://stores.shop.ebay.co.uk/D-S-MOTORSPORT-PERFORMANCE-PARTS.  Will cost more for the postage than the cost of the item.  They are made in different materials, my original one is made of a compressed fibre but come in a material like bakelite, acrylic etc. You could make your own if you have the material, the pattern is easy enough to duplicate.
    Cheers,
    Len
     
    #2
    martymexico
    Deity
    • Total Posts : 2426
    • Scores: 274
    • Reward points: 5829
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: online
    Re: Pinto Fuel Pump Spacer 2015/10/04 13:52:24 (permalink)
    0
    Make one from a chunk of Ally...
    #3

    troppo
    Aficionado
    • Total Posts : 376
    • Scores: 8
    • Reward points: 3498
    • Joined: 2014/01/05 13:45:37
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/04 16:55:44 (permalink)
    0
    I`ll see if i can find mine, i`m going with an electric pump so wont need it. Could take me a week or so to find it but its yours if i can
     
    #4
    Drewdog
    Deity
    • Total Posts : 1028
    • Scores: 118
    • Reward points: 5323
    • Joined: 2013/03/06 22:31:01
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/04 19:20:28 (permalink)
    0
    Hey Troppo, double check before you put the blanking plate over the old hole, mine still needed it, the little pump lobe, actuator thingy (not sure what its called) clashed with the blanking plate... 
    Cheers Drew... 

    GT Cortina Project "The Ugly Duckling"
    #5
    troppo
    Aficionado
    • Total Posts : 376
    • Scores: 8
    • Reward points: 3498
    • Joined: 2014/01/05 13:45:37
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/04 19:47:44 (permalink)
    0
    Drewdog
    Hey Troppo, double check before you put the blanking plate over the old hole, mine still needed it, the little pump lobe, actuator thingy (not sure what its called) clashed with the blanking plate... 
    Cheers Drew... 


    Thanks mate, never even thought of that, was just going to blank it off. Might need it after all, sorry Jaycees, i`ll have to check
     
     
     
    post edited by troppo - 2015/10/04 19:56:03
    #6

    NQRS
    Deity
    • Total Posts : 897
    • Scores: 58
    • Reward points: 6931
    • Joined: 2011/08/01 11:02:49
    • Location: Townsville QLD Australia
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/04 20:11:53 (permalink)
    0
    I removed the pump actuator shaft from the block before fitting the blanking plate as I use an electric pump. used 6mm steel  flat with gasket with silicon to seal it to prevent oil leaks due to my high oil pressure.
    #7
    Jaycees
    Aficionado
    • Total Posts : 400
    • Scores: 7
    • Reward points: 4432
    • Joined: 2011/08/01 11:02:49
    • Location: Windsor nsw Australia
    • Status: offline
    Re: Pinto Fuel Pump Spacer 2015/10/05 21:33:11 (permalink)
    0
    Thanks Guys for your input , very helpful
    Jim
    #8
    Jump to:
    © 2025 APG vNext Trial Version 5.1