Go back to home

Sleaving block. - max size?

Author
Post
Essentials Only Full Version
escortinadriver
Deity
  • Total Posts : 1277
  • Scores: 115
  • Reward points: 6061
  • Joined: 2011/08/01 11:02:49
  • Location: Vic Australia
  • Status: offline
2010/12/05 13:41:34 (permalink)
0

Sleaving block. - max size?

What are the largest bore/sleaves you can fit in a pinto block?

What is the bore spacing??? I dont have access to a block atm?

I'm guessing it would need the bottom grout filled to retain some strength.....?

Shaun
#1


11 Replies Related Threads
    maxrs
    Scholar
    • Total Posts : 1334
    • Scores: 1
    • Reward points: 4483
    • Joined: 2011/08/01 11:02:49
    • Location: Mango hill Queensland Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/12/05 19:14:15 (permalink)
    0
    Max bore size without sleeving is around 1MM over sized, add another 20 thou if your game.
    #2
    martymexico
    Deity
    • Total Posts : 2428
    • Scores: 274
    • Reward points: 5829
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/12/05 19:23:17 (permalink)
    0
    I bored an old 76 Cortina Pinto block out to 93.5mm, had it sonic tested just incase of weaknesses. Only drama i had was the side core plug 'walking out' due to minor flexing[B)], Its still getting around some 10yrs later. I have heard of 95mm with a 200/205 block as they've thicker walls etc, 93mm should be safe for most road tunings for a stocker Escort block.
    #3

    escortinadriver
    Deity
    • Total Posts : 1277
    • Scores: 115
    • Reward points: 6061
    • Joined: 2011/08/01 11:02:49
    • Location: Vic Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/12/05 19:49:10 (permalink)
    0
    Marty,

    I'm talking max size, as in fitting new cast liners. I think I recall the Finish guys gutting the centers and using 100mm bores with their custom alloy heads? Just in theory atm....[8~2]

    Shaun
    #4
    martymexico
    Deity
    • Total Posts : 2428
    • Scores: 274
    • Reward points: 5829
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/12/05 20:32:48 (permalink)
    0
    100mm ?!**^%, thats v8 size!! Luckily i've never had to install liners. I just went out to measure the gap between bores(std size) and is 11.5m-12.0mm, the closest hole is the water jacket at approx 8mm, hope this helps..
    #5
    oldesky2lt
    Enthusiast
    • Total Posts : 45
    • Scores: 0
    • Reward points: 1281
    • Joined: 2011/08/01 11:02:49
    • Location: melbourne victoria Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/13 21:47:02 (permalink)
    0
    G'day Shaun,

    Your always a little outside the square

    1275 Mini blocks have offset bores, could be possible with a pinto ????

    Chris
    #6

    Mk1 Lotus
    Supporter
    • Total Posts : 204
    • Scores: 3
    • Reward points: 2811
    • Joined: 2011/08/01 11:02:49
    • Location: Sydney Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/14 07:41:17 (permalink)
    0
    The alloy Cosworth blocks which have siamese bores have been taken to 97mm with a liner and there was talk of trying direct plating to get them to 100mm.

    If you wanted to go even 97mm you need to have the sleeves made in one piece to do it properly, a half arsed way would be to machine flats on sleeves to create a siamese bore.
    #7
    escortinadriver
    Deity
    • Total Posts : 1277
    • Scores: 115
    • Reward points: 6061
    • Joined: 2011/08/01 11:02:49
    • Location: Vic Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/14 09:48:34 (permalink)
    0
    Thanks Paul,

    I'll have to have a bit more of a look into it then. Was just going on what I remembered which can be a little hazy at times....

    Thanks Chris,

    Thinking outside the square has always been my forte. I'll take it as a compliment

    The question came about as I am having some new o/s sleaves fitted in my brothers bike for yet another fankenstein creation of mine

    Shaun

    #8
    oldesky2lt
    Enthusiast
    • Total Posts : 45
    • Scores: 0
    • Reward points: 1281
    • Joined: 2011/08/01 11:02:49
    • Location: melbourne victoria Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/14 14:44:54 (permalink)
    0
    Hi Shaun

    Was meant as a compliment

    Bloody boring when everyone is in the same square

    Chris
    #9
    escortinadriver
    Deity
    • Total Posts : 1277
    • Scores: 115
    • Reward points: 6061
    • Joined: 2011/08/01 11:02:49
    • Location: Vic Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/14 15:42:37 (permalink)
    0


    No worries, just as I thought..

    Shaun
    #10
    Roger Miller
    Enthusiast
    • Total Posts : 72
    • Scores: 0
    • Reward points: 681
    • Joined: 2011/08/01 11:02:49
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/16 10:30:19 (permalink)
    0
    Shaun,

    talk to Minilight man

    [Leon]
    #11
    escortinadriver
    Deity
    • Total Posts : 1277
    • Scores: 115
    • Reward points: 6061
    • Joined: 2011/08/01 11:02:49
    • Location: Vic Australia
    • Status: offline
    RE: Sleaving block. - max size? 2010/05/16 21:53:03 (permalink)
    0
    Thanks Roger,

    I'll send him an email.

    Shaun
    #12
    Jump to:
    © 2025 APG vNext Trial Version 5.1