Go back to home

Mounting hard fuel lines

Author
BootOn
Enthusiast
  • Total Posts : 205
  • Scores: 0
  • Reward points: 3439
  • Joined: 2011/08/01 11:02:49
  • Location: Sydney NSW Australia
  • Status: offline
2018/05/25 13:14:38 (permalink)
0

Mounting hard fuel lines

Hi

I’m at a point where I need to run fuel flow and return hard lines the length of the car for an EFI conversion, I don’t want to run through the passenger compartment so the most logical place to run is along side the drivers side chassis rail. I’m reluctant to drill the chassis rail or floor pan to mount the clips so was wondering if anyone has any bright ideas?

My panel welding is not great so I’d prefer not to weld brackets. I was thinking about maybe epoxy panel bond some brackets on but don’t want them to fall off down the track.

Advice, photos, anything welcome

Cheers
#1


6 Replies Related Threads

    Matt75
    Deity
    • Total Posts : 2184
    • Scores: 67
    • Reward points: 5609
    • Joined: 2011/08/01 11:02:49
    • Location: Doncaster Vic Australia
    • Status: offline
    Re: Mounting hard fuel lines 2018/05/25 14:07:16 (permalink)
    0
    Why not use rivnuts?

     
    My 4 door MK II Resto
    http://www.classic-ford.org/cfp/tm.aspx?m=37623

    RS Owners Club Victoria Committee Member - http://rsocvic.com/
     
     
    #2
    Paul Dunstan
    Supporter
    • Total Posts : 1378
    • Scores: 35
    • Reward points: 4790
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide SA Australia
    • Status: offline
    Re: Mounting hard fuel lines 2018/05/25 18:24:06 (permalink)
    0
    Yep. Agree with above 👍

    Cheers

    Paul
    #3

    BootOn
    Enthusiast
    • Total Posts : 205
    • Scores: 0
    • Reward points: 3439
    • Joined: 2011/08/01 11:02:49
    • Location: Sydney NSW Australia
    • Status: offline
    Re: Mounting hard fuel lines 2018/05/26 07:15:34 (permalink)
    0
    Into the side of the chassis rail?
    What’s the best way to passivate the hole after drilling it, grind around it and paint?
    #4
    escortinadriver
    Deity
    • Total Posts : 1278
    • Scores: 115
    • Reward points: 6097
    • Joined: 2011/08/01 11:02:49
    • Location: Vic Australia
    • Status: offline
    Re: Mounting hard fuel lines 2018/05/27 23:07:34 (permalink)
    0
    Yep, I just used aluminium P Clips with the rubber sleeve.
     
     
    I drilled slightly oversize rivet holes into chassis, quick lick of rust preventative paint, then riveted into place. 
     
    Shaun
     
     

    'If I'd asked what people had wanted, they'd have said faster horses....' Henry Ford
    #5
    BootOn
    Enthusiast
    • Total Posts : 205
    • Scores: 0
    • Reward points: 3439
    • Joined: 2011/08/01 11:02:49
    • Location: Sydney NSW Australia
    • Status: offline
    Re: Mounting hard fuel lines 2018/05/31 14:13:54 (permalink)
    0
    Thanks for the replies. Sounds good 👍🏻
    #6

    leerousi
    Enthusiast
    • Total Posts : 4
    • Scores: 0
    • Reward points: 3
    • Joined: 2018/12/03 20:20:05
    • Status: offline
    Re: Mounting hard fuel lines 2018/12/03 20:45:02 (permalink)
    0
    No offense, but I brought some windshield rubber from the old and new car companies to capri
     
    It's a nightmare either they made a mistake in your model or Chinese made it took 4 hours to try to get the rear windshield finally I gave up and sent them back just not fit or want to go in. I sent them back even sent one in front of them even didn't want to try Try one of the fiasco behind it.. think the window channel has a problem...

    So I cleaned my ones, in the 2 minute windshield...

    Thank you all for your kindness to me, I wish you good health and good luck!
    #7
    Jump to:
    © 2025 APG vNext Trial Version 5.1