gtv6capri
Deity
- Total Posts : 1461
- Scores: 53
- Reward points: 5548
- Joined: 2011/08/01 11:02:49
- Location: Melbourne Vic Australia
- Status: offline
RE: Mk 3 Ive brought
2008/01/12 14:14:22
(permalink)
I have a brand new seal if thats the problem.
Car looks a million dollars, stick a set of 15" gold Simmons on it and the MK3 "S" stripe in gold, mmmmmmmm
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2008/01/12 18:50:08
(permalink)
Hi JR - i have black S pak stripes on it - its not hte seal but i wouldn't mind a new one! Do u still have the Simmons? Im going to run falcon stud pattern - all is ready! I have a couple of other mk 3 spoilers in NZ wools - if u r keen!
|
muzwaldo
Enthusiast
- Total Posts : 88
- Scores: 0
- Reward points: 5363
- Joined: 2011/08/01 11:02:49
- Location: Dublin Ireland
- Status: offline
RE: Mk 3 Ive brought
2008/01/12 22:50:27
(permalink)
Hi Stefan,
The MkIII has come up well, looking great.
Can you tell me about the BW diff you are using? Obviously you are shortening one - have you managed to find a place to get it done for a good price?
I have an XR8 Falcon diff ready for mine so any tips would be appreciated. Some places want drug money to do the shortening?
Cheers
Steve.
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2008/02/12 07:42:45
(permalink)
Hi - Supa Trik engineering (Dandenong Melbourne) r doing mine - $350 to shorten + $150 4 axle(s). Ive re-built heaps of these so will disassemble // re-assemble it myself. I picked up the diff - disc to disc $180 - they dont break easy so cheap to buy. Running 3:1 LSD. The total width is 1385cm - standard mk 1. That way i can fit 14 x 8's under no probs (the mk 3 diff is 1450cm
|
gtv6capri
Deity
- Total Posts : 1461
- Scores: 53
- Reward points: 5548
- Joined: 2011/08/01 11:02:49
- Location: Melbourne Vic Australia
- Status: offline
RE: Mk 3 Ive brought
2008/02/12 13:38:38
(permalink)
Stef, I'll give you the seal for 2 nice J moulds mine were rubbed back and painted and although straight, wont go back to chrome.
Let me know what colour carpet you want and I'll get it pressed for you as the factory will most likely close over xmas
Oh Simmons are gone, they were 14" and 4 stud anyway, falcon ones should be easy to get (and cheaper)
Yes MK2/3 diff is a few inches wider than MK1, the racers used to swap to MK1 diffs to get more rubber under the rear
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2008/02/12 17:53:06
(permalink)
Hi JR - if its okay i dont need the carpet. Ive also sold a lot of my Mk 1 stuff - no J trims left - only dented ones. Yes i went falcon b/c of hte wider choice. She's booked in next Tuesday 4 the central locking// alarm etc and wed//thurs for the new hood lining // sun roof service so getting there!
|
V8GFISH
Enthusiast
- Total Posts : 63
- Scores: 0
- Reward points: 0
- Joined: 2011/08/01 11:02:49
- Location: Perth WA Australia
- Status: offline
RE: Mk 3 Ive brought
2008/06/12 23:35:49
(permalink)
Nice looking car Spud, ya don't see many around over here.
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/07/06 11:33:43
(permalink)
Thanks V8 fish. Well finally getting my but into action - sold the diff etc so have to start the project now!  new control arms and tie rod ends - have reco'd a power steer rack for it as well  new konis front and rear - ill keep the single leafs but new bushes.
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/07/06 11:40:29
(permalink)
replacement ford 5 stud hubs (UPS - bayswater Melbourne) 
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/07/06 11:51:31
(permalink)
engine wise - an explorer 4.0ltr V6. These are a later version of the 2.8 V6 the car runs. Only diffs are: 1. Coil packs instead of the dizzy - u can see where they have blanked the original off. 2. Aluminium 3 port heads - vs the old cast iron siamese 3. overhaed cams - they deleted the in block cam - replaced it with a jack shaft to drive the over heads 4. 4ltr vs 2.8 The 2.8 5 speed bolts straight up // the drivers side engine mount bolts straight up. But the casting of the block - passengers side has been changed. I am having a new intake made - the 4.0ltr one is plastic Am using the coil packs, EDIS module and a meja jolt to drive the whole lot the donor car - 98 explorer engine  drivers side - not aluminium 3 port heads - coil packs - casting same as 2.8  pass side - casting different  mega jolt  
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/07/06 11:56:55
(permalink)
ford RS X pack archs  rs motif 
|
V8GFISH
Enthusiast
- Total Posts : 63
- Scores: 0
- Reward points: 0
- Joined: 2011/08/01 11:02:49
- Location: Perth WA Australia
- Status: offline
RE: Mk 3 Ive brought
2009/07/06 14:09:46
(permalink)
This should be an interesting fit, good info Spud
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/08/06 22:40:59
(permalink)
No - i haven't wools - didn't know - did u see the orange mk 3 on trade me - your color!
|
spud15
Supporter
- Total Posts : 1237
- Scores: 36
- Reward points: 5597
- Joined: 2011/08/01 11:02:49
- Location: Melbourne
- Status: offline
RE: Mk 3 Ive brought
2009/10/06 14:49:44
(permalink)
UPC 298 OD rotors // 28ml thick with AP racing, radial mount 4 pot calipers 
|
hotboostgt
Aficionado
- Total Posts : 532
- Scores: 4
- Reward points: 5440
- Joined: 2011/08/01 11:02:49
- Location: nth brisbane qld Australia
- Status: offline
RE: Mk 3 Ive brought
2009/10/06 17:10:09
(permalink)
Nice spud , can I ask how much and where from did you get those awsome brakes.Im thinking going the volvo 4 pot with tx3 rotors.
|