Go back to home

zetec crank position sensor housing.

Author
Post
Essentials Only Full Version
GYRO
Enthusiast
  • Total Posts : 58
  • Scores: 0
  • Reward points: 2471
  • Joined: 2017/12/27 16:35:44
  • Location: Perth WA
  • Status: offline
2018/12/31 19:08:04 (permalink)
0

zetec crank position sensor housing.

Gday guys, I need a cps housing for a 2.0 zetec engine with manual box. Ford no longer have them. The p/n is F5RZ-6K341-A. PLS HELP.
#1


6 Replies Related Threads
    lee_doidge
    Enthusiast
    • Total Posts : 128
    • Scores: 3
    • Reward points: 3394
    • Joined: 2015/05/14 15:09:47
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/01 13:11:43 (permalink)
    0
    Hey mate,
     
    Feel your pain, bought a zetec from a wreckers. Got it turned around and installed in my mk2 and
    only then found out the CPS sensor couldnt see the the flywheel when i was trying to fire it for the first time.
    Then learnt all about automatic and manual zetecs. Wish I had an easy solution for you but in the end it was
    chasing down lots of wreckers and paying top $$$ to get the right part. Then had to pull the gearbox off to swap it out. Not one of my finer moments...
     
    Best of luck with the hunt. 
    #2
    martymexico
    Deity
    • Total Posts : 2440
    • Scores: 285
    • Reward points: 5832
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/01 23:28:04 (permalink)
    0
    Gyro
    Chase one from USA eBay, gen Ford ones for less than $50 , infact get a few and sell on the others to recoup your funds ..

    Edit
    I looked around and found this...
    https://rover.ebay.com/ro...k%2Fitm%2F254009979070
    Cheers
    post edited by martymexico - 2019/01/01 23:42:01
    #3

    GYRO
    Enthusiast
    • Total Posts : 58
    • Scores: 0
    • Reward points: 2471
    • Joined: 2017/12/27 16:35:44
    • Location: Perth WA
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/02 13:36:00 (permalink)
    0
    Tks Marty. 
    #4
    GYRO
    Enthusiast
    • Total Posts : 58
    • Scores: 0
    • Reward points: 2471
    • Joined: 2017/12/27 16:35:44
    • Location: Perth WA
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/16 14:51:03 (permalink)
    0
    G,day guys, Just an update on this subject. I just received cps housing from Kitspares UK. luckily tried to fit sensor with housing installed in block and found it would not fit. I have had to elongate hole otherwise sensor fouls on block. This may only be a problem on the 2.0 engine and Kitspares are not aware. I will email them. Would be very annoyed if replacing a duff sensor required engine removal. Cheers.  
    #5
    lee_doidge
    Enthusiast
    • Total Posts : 128
    • Scores: 3
    • Reward points: 3394
    • Joined: 2015/05/14 15:09:47
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/16 14:57:59 (permalink)
    0
    that reminds, was just on the retroford website and Dave is now stocking them.
     
    http://www.retro-ford.co....nk-sensor-bracket-z075
    #6

    martymexico
    Deity
    • Total Posts : 2440
    • Scores: 285
    • Reward points: 5832
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/17 22:54:17 (permalink)
    0
    I feel bad cause i found the link for you , hope all works out fine mate , report back when it's time to start the motor
    #7
    Jump to:
    © 2025 APG vNext Trial Version 5.1