Go back to home

Pinto Power Leaderboard

Page: < 123 Showing page 3 of 3 - Powered by APG vNext Trial
Author
Post
Essentials Only Full Version
2lt_Scort
Supporter
  • Total Posts : 1285
  • Scores: 23
  • Reward points: 5188
  • Joined: 2011/08/01 11:02:49
  • Location: Adelaide Australia
  • Status: offline
Re:Pinto Power Leaderboard 2017/03/09 11:36:55 (permalink)
0
ratta tat tat
I think this the motor with Sierra manifold. Saw something on facebook a while back. Huge numbers there! I was thinking of going a GT3071R but worried about lag. What do you reckon Milan :D?




I always thought based on previous reading the Sierra manifold didn't flow too well for big figures.... looks like if its pumped through with enough force it does fine?
 

Mk2 2dr 2lt EFI quad T/B's
Mk2 2dr Track Car project
Mk1 2dr
Mk2 2dr 2lt (Sold)
#31
RSWEPN
Enthusiast
  • Total Posts : 138
  • Scores: 1
  • Reward points: 3302
  • Joined: 2011/08/01 11:02:49
  • Location: Sydney NSW Australia
  • Status: offline
Re:Pinto Power Leaderboard 2017/03/20 19:43:12 (permalink)
+1 (1)
escortinadriver
Nice work!
 
What is you engine spec Milan and do you have a photo of the graph with the rpm visible?
 
Thanks, SHaun



Hey, 2L with forged internals, ported head, oversize valves, sierra intake, GT3076 with .63 housing, 3inch exhaust etc etc

Dont have it with rpm, its going back on the dyno soon for more power so ill get a graph with RPM.


ratta tat tat
I think this the motor with Sierra manifold. Saw something on facebook a while back. Huge numbers there! I was thinking of going a GT3071R but worried about lag. What do you reckon Milan :D?



Mines pretty laggy, but the cam that was in it was not suited to a turbo engine. Ive now changed the cam and should come on alot eariler. Your GT3071R should be great, i should have got the same turbo as you.



Cheers

Milan
#32
ratta tat tat
Supporter
  • Total Posts : 1633
  • Scores: 39
  • Reward points: 5492
  • Joined: 2011/08/01 11:02:49
  • Location: Brisbane
  • Status: offline
Re:Pinto Power Leaderboard 2017/11/29 22:41:01 (permalink)
+1 (1)
RSWEPN

Mines pretty laggy, but the cam that was in it was not suited to a turbo engine. Ive now changed the cam and should come on alot eariler. Your GT3071R should be great, i should have got the same turbo as you.






Nice one. I never bought that turbo, I went with a GT2860RS. Made 271hp at the tyres yesterday. The car has one more run in the morning after swapping fuel pumps and should get 300 or very close to it. E85 with 16 pounds of boost, 6000rpm.
post edited by ratta tat tat - 2017/11/29 22:46:58
#33

2lt_Scort
Supporter
  • Total Posts : 1285
  • Scores: 23
  • Reward points: 5188
  • Joined: 2011/08/01 11:02:49
  • Location: Adelaide Australia
  • Status: offline
Re:Pinto Power Leaderboard 2017/12/01 09:27:30 (permalink)
0
Good result.
What inlet and t/b did you use Hayden?
 
THanks,
Rhys

Mk2 2dr 2lt EFI quad T/B's
Mk2 2dr Track Car project
Mk1 2dr
Mk2 2dr 2lt (Sold)
#34
ratta tat tat
Supporter
  • Total Posts : 1633
  • Scores: 39
  • Reward points: 5492
  • Joined: 2011/08/01 11:02:49
  • Location: Brisbane
  • Status: offline
Re:Pinto Power Leaderboard 2018/07/20 22:24:39 (permalink)
0
Thanks Rhys. Final figure was 301hp 20psi. Standard Sierra injection manifold & throttle body.
Did you know the throttle body size on a SR20DET is smaller than SR20DE? That's how I knew the standard sierra one would be ok :)
#35
2lt_Scort
Supporter
  • Total Posts : 1285
  • Scores: 23
  • Reward points: 5188
  • Joined: 2011/08/01 11:02:49
  • Location: Adelaide Australia
  • Status: offline
Re:Pinto Power Leaderboard 2018/07/22 17:11:02 (permalink)
0
Yes I've read that somewhere. All good knowledge, stuff I should have found out earlier and saved myself a few hassles 
If/when I finish that car, its likely to be on a std Sierra inlet.

Mk2 2dr 2lt EFI quad T/B's
Mk2 2dr Track Car project
Mk1 2dr
Mk2 2dr 2lt (Sold)
#36

Page: < 123 Showing page 3 of 3 - Powered by APG vNext Trial
Jump to:
© 2025 APG vNext Trial Version 5.1