Go back to home


We have detected that you are using ad blocking software.
The Classic Ford forum is made possible by ad revenue.
Please disable your ad blocker to ensure that this site lives on.

Hot!zetec crank position sensor housing.

Author
GYRO
Enthusiast
  • Total Posts : 15
  • Scores: 0
  • Reward points: 509
  • Joined: 2017/12/27 16:35:44
  • Location: Perth WA
  • Status: offline
2018/12/31 19:08:04 (permalink)
0

zetec crank position sensor housing.

Gday guys, I need a cps housing for a 2.0 zetec engine with manual box. Ford no longer have them. The p/n is F5RZ-6K341-A. PLS HELP.
#1


6 Replies Related Threads

    Lee
    Enthusiast
    • Total Posts : 118
    • Scores: 2
    • Reward points: 1400
    • Joined: 2015/05/14 15:09:47
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/01 13:11:43 (permalink)
    0
    Hey mate,
     
    Feel your pain, bought a zetec from a wreckers. Got it turned around and installed in my mk2 and
    only then found out the CPS sensor couldnt see the the flywheel when i was trying to fire it for the first time.
    Then learnt all about automatic and manual zetecs. Wish I had an easy solution for you but in the end it was
    chasing down lots of wreckers and paying top $$$ to get the right part. Then had to pull the gearbox off to swap it out. Not one of my finer moments...
     
    Best of luck with the hunt. 
    #2
    martymexico
    Deity
    • Total Posts : 1122
    • Scores: 37
    • Reward points: 3326
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/01 23:28:04 (permalink)
    0
    Gyro
    Chase one from USA eBay, gen Ford ones for less than $50 , infact get a few and sell on the others to recoup your funds ..

    Edit
    I looked around and found this...
    https://rover.ebay.com/ro...k%2Fitm%2F254009979070
    Cheers
    post edited by martymexico - 2019/01/01 23:42:01
    #3

    GYRO
    Enthusiast
    • Total Posts : 15
    • Scores: 0
    • Reward points: 509
    • Joined: 2017/12/27 16:35:44
    • Location: Perth WA
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/02 13:36:00 (permalink)
    0
    Tks Marty. 
    #4
    GYRO
    Enthusiast
    • Total Posts : 15
    • Scores: 0
    • Reward points: 509
    • Joined: 2017/12/27 16:35:44
    • Location: Perth WA
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/16 14:51:03 (permalink)
    0
    G,day guys, Just an update on this subject. I just received cps housing from Kitspares UK. luckily tried to fit sensor with housing installed in block and found it would not fit. I have had to elongate hole otherwise sensor fouls on block. This may only be a problem on the 2.0 engine and Kitspares are not aware. I will email them. Would be very annoyed if replacing a duff sensor required engine removal. Cheers.  
    #5
    Lee
    Enthusiast
    • Total Posts : 118
    • Scores: 2
    • Reward points: 1400
    • Joined: 2015/05/14 15:09:47
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/16 14:57:59 (permalink)
    0
    that reminds, was just on the retroford website and Dave is now stocking them.
     
    http://www.retro-ford.co....nk-sensor-bracket-z075
    #6
    martymexico
    Deity
    • Total Posts : 1122
    • Scores: 37
    • Reward points: 3326
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    Re: zetec crank position sensor housing. 2019/01/17 22:54:17 (permalink)
    0
    I feel bad cause i found the link for you , hope all works out fine mate , report back when it's time to start the motor
    #7
    Jump to:

    © 2019 APG vNext Commercial Version 5.1