Go back to home

v6 head gaskets

Author
Post
Essentials Only Full Version
in rod we trust
Aficionado
  • Total Posts : 447
  • Scores: 4
  • Reward points: 1985
  • Joined: 2016/02/27 17:13:04
  • Status: offline
2017/12/29 17:26:32 (permalink)
0

v6 head gaskets

im thinking of sending the heads away to get them done for unleaded fuel and larger valves put in to match the port work on em
 
im after a good set of head gaskets people have used and are proven ive noticed on the or most sets i have they dont look to good and seem pretty cheap crap ..
im after a set that have the raised seal around the water jackets and borders  .. like these i see payden have some and this other brand ... anybody used these or these style or any similar that a a good gasket
 
https://www.ebay.co.uk/itm/FORD-GRANADA-CAPRI-ZODIAC-GILBERN-INVADER-GENIE-ESSEX-V6-3-0-HEAD-GASKET-SET/352102874149?hash=item51faf77c25:g:ouUAAOSwcUBYQxPX
 
https://www.ebay.co.uk/it...f0e:g:V6gAAOSwv-ZZ~CuR
 
by the way hope you all had a great christmas and have a happy great new yr
#1


4 Replies Related Threads
    Johnscapris
    Enthusiast
    • Total Posts : 98
    • Scores: 5
    • Reward points: 5609
    • Joined: 2011/08/01 11:02:49
    • Location: Morayfield Qld Australia
    • Status: offline
    Re: v6 head gaskets 2017/12/29 18:03:13 (permalink)
    0
    Forum member,
     
    Most head gaskets fail due to the following:   1.  Unclean surfaces
                                                                     2.  Block and or head surfaces not perfectly flat. Have surfaces machined.
                                                                     3.  Stretched head bolts.  Should replace with new.
                                                                     4.  Bolts bottoming out after machineing to block and heads.
                                                                     5.  Incorrect torque tightening.
     
    I install head gaskets dry and use ACL brand gaskets up to about 170HP and Cometec brand from 170HP to 220HP and then custom made (with a fire ring).
    This may assist.
     
    Regards
    John
     
     
     
    #2
    Flighter
    Deity
    • Total Posts : 1107
    • Scores: 43
    • Reward points: 5151
    • Joined: 2011/10/17 14:55:59
    • Status: offline
    Re: v6 head gaskets 2017/12/29 18:53:33 (permalink)
    0
    Victor Reinz gaskets have a good rep for the Pinto, so you might like to look into them too. Available at Burton's and probably eBay UK.

    WTB: Recaro seat - any condition considered
     
     
    #3

    GTV6
    Master
    • Total Posts : 736
    • Scores: 34
    • Reward points: 5871
    • Joined: 2011/08/01 11:02:49
    • Location: Perth WA Australia
    • Status: offline
    Re: v6 head gaskets 2017/12/29 19:43:36 (permalink)
    0
    Some also let go due to inlet manifold corrosion.  Don't forget to get the inlet manifold machined to match as well, and be sure to check if what you end up getting are mono torque or require a re-torque.  I blew a set in between torques when I was a young fella, but I was being stupid doing a burn out with a brand new engine.
    #4
    gtv6capri
    Deity
    • Total Posts : 1461
    • Scores: 53
    • Reward points: 5548
    • Joined: 2011/08/01 11:02:49
    • Location: Melbourne Vic Australia
    • Status: offline
    Re: v6 head gaskets 2017/12/29 20:26:22 (permalink)
    0
    You can get Permaseal sets from South Africa, a friend has some here in Melbourne

    Capri The car I always promised myself
    #5
    Jump to:
    © 2025 APG vNext Trial Version 5.1