Go back to home

Volvo/BMW brake modes

Author
Post
Essentials Only Full Version
troppo
Aficionado
  • Total Posts : 376
  • Scores: 8
  • Reward points: 3498
  • Joined: 2014/01/05 13:45:37
  • Status: offline
2014/07/01 17:18:53 (permalink)
0

Volvo/BMW brake modes

Has anyone done this conversion? Volvo 240 calipers with BMW A30 discs. I was wondering if i could still keep mt 13`s with this mod or do i need larger wheels?
Cheers
Troppo
 
#1


4 Replies Related Threads
    Matt75
    Deity
    • Total Posts : 2184
    • Scores: 67
    • Reward points: 5609
    • Joined: 2011/08/01 11:02:49
    • Location: Doncaster Vic Australia
    • Status: offline
    Re: Volvo/BMW brake modes 2014/07/01 20:37:52 (permalink)
    0
    Hi Mate,
     
    I used the Laser TX3 rotors as you don't need to mod the hubs.
     
    They will fit fine under 13"rims
     
    Cheers,
     
    Matt

     
    My 4 door MK II Resto
    http://www.classic-ford.org/cfp/tm.aspx?m=37623

    RS Owners Club Victoria Committee Member - http://rsocvic.com/
     
     
    #2
    troppo
    Aficionado
    • Total Posts : 376
    • Scores: 8
    • Reward points: 3498
    • Joined: 2014/01/05 13:45:37
    • Status: offline
    Re: Volvo/BMW brake modes 2014/07/01 20:47:35 (permalink)
    0
    Great, thanks for that Matt. Will the volvo calipers work with tx3 rotors?
     
    #3

    RS 2000
    Deity
    • Total Posts : 536
    • Scores: 51
    • Reward points: 6199
    • Joined: 2011/08/01 11:02:49
    • Location: South Australia
    • Status: offline
    Re: Volvo/BMW brake modes 2014/07/01 23:42:46 (permalink)
    +1 (1)
    troppo
    Great, thanks for that Matt. Will the volvo calipers work with tx3 rotors?
     


    yes they will, I use same setup on my RS.
     
    cheers

    1979 RS 2000 - SR20DET
     http://www.classic-ford.org/cfp/tm.aspx?m=48366
    PERFORMANCE AUTO & DYNO
    https://www.facebook.com/PerformanceAutoDyno/
    https://www.performanceautodyno.com.au/
    #4
    Gdub
    Master
    • Total Posts : 927
    • Scores: 32
    • Reward points: 2475
    • Joined: 2011/08/01 11:02:49
    • Location: Melbourne Vic
    • Status: offline
    Re: Volvo/BMW brake modes 2014/07/02 11:08:26 (permalink)
    0
    The benefit of the BMW rotors is they are WAY thicker than the TX3. I suspect using TX3 that by the time the pads are worn right down the pistons could be close to popping out of the calipers.  Would never be an issue of course if you change the pads when they are down to about 25%.
    The BMW rotors need the centre hole bored out to suit the escort hub and also redrilling for the bolt pattern.  You will also need to have 2.5mm machined off the front edge of the rotor where it mates to the hub and also 2.5mm off the opposing face on the hub.  If you dont the inside of the rotor will foul on the tie rod end.
     
    I use the BMW / Volvo combination and it works well and fits under 13" wheels. You just cant use stick on wheel weights on the inside of your wheels or they will hit the caliper.  Knock on weights arent a problem.
    post edited by Gdub - 2014/07/02 11:14:54

    Make it go FASTER!
     
    #5
    Jump to:
    © 2025 APG vNext Trial Version 5.1