Go back to home

bolt holes for RS2000 seats

Author
Post
Essentials Only Full Version
retro666
Enthusiast
  • Total Posts : 203
  • Scores: 5
  • Reward points: 2901
  • Joined: 2014/01/10 10:34:22
  • Location: Forster NSW
  • Status: offline
2014/03/10 15:53:37 (permalink)
0

bolt holes for RS2000 seats

Hi, I am doing up a Mk2 van that has RS2000 seats fitted but I am not sure if its right. Could someone give me the bolt spacings and locations on a RS2000 floor. I am replacing the seat riser and part of the floors so the holes can be drilled in the correct places.
#1


7 Replies Related Threads
    retro666
    Enthusiast
    • Total Posts : 203
    • Scores: 5
    • Reward points: 2901
    • Joined: 2014/01/10 10:34:22
    • Location: Forster NSW
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/20 20:48:37 (permalink)
    0
    Anyone with a RS2000 could they measure the bolt spacing and placement as the floor is getting close. Thanks
    #2
    martymexico
    Deity
    • Total Posts : 2442
    • Scores: 286
    • Reward points: 5832
    • Joined: 2011/08/01 11:02:49
    • Location: Adelaide Sth Aust Australia
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/21 16:42:32 (permalink)
    0
    Aren't they mounted in the same holes as the ghia models? And the rear floor has stamped holes where they should go. Just a guess as I've not owned a RS for many years.
    #3

    retro666
    Enthusiast
    • Total Posts : 203
    • Scores: 5
    • Reward points: 2901
    • Joined: 2014/01/10 10:34:22
    • Location: Forster NSW
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/21 17:07:26 (permalink)
    0
    I dont know, there is many holes been drilled and I dont know if any are right.
    #4
    Drewdog
    Deity
    • Total Posts : 1031
    • Scores: 119
    • Reward points: 5332
    • Joined: 2013/03/06 22:31:01
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/22 18:34:03 (permalink)
    0
    Bare with me, my RS comes back from the panel shop on Monday, I'll get some pics and measurements for you early next week......

    GT Cortina Project "The Ugly Duckling"
    #5
    retro666
    Enthusiast
    • Total Posts : 203
    • Scores: 5
    • Reward points: 2901
    • Joined: 2014/01/10 10:34:22
    • Location: Forster NSW
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/22 20:55:44 (permalink)
    0
    Many thanks, sounds great.
    #6

    Drewdog
    Deity
    • Total Posts : 1031
    • Scores: 119
    • Reward points: 5332
    • Joined: 2013/03/06 22:31:01
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/24 17:27:01 (permalink)
    0
    The holes are in the centre of the the rail, the first one, outside sill side, to the centre of the hole is 130mm, then from centre of that to the centre of the next one is 325mm, you should be able to mark the rears from that as there is no real point to measure with the curve of the floorpan.... The bolts are captive/ welded in, may be a challenge on the from as there is no access underneath the rail....
    Hope that helps, good luck..... Drewdog............

    Attached Image(s)


    GT Cortina Project "The Ugly Duckling"
    #7
    retro666
    Enthusiast
    • Total Posts : 203
    • Scores: 5
    • Reward points: 2901
    • Joined: 2014/01/10 10:34:22
    • Location: Forster NSW
    • Status: offline
    Re: bolt holes for RS2000 seats 2014/03/24 17:39:10 (permalink)
    0
    OK thanks. Ive nearly done one floor and making a new seat riser is next. I can weld the nuts on before the riser is welded in.
    #8
    Jump to:
    © 2025 APG vNext Trial Version 5.1