Workshop Tips and Tricks

To Bottom

Workshop Tips and Tricks (p.2)
Post New Thread
Regular
RSman4ever

pinto head studs

Hey guys I have a SMALL issue with one of the head studs on my engine, I couldnt buy quality spline bits individually so I got a set from repco. It turns out that the bits are probably a little bit on the soft side, by the time I got to the LAST stud it was a bit worn and has damaged the head on the..
1
2013/01/03 22:17:42
the_cheese

Replacing wheel studs without taking off hubs?

Hi guys Well got my mk2 back on the road after a redoing the front end and getting a set of minilights from JBW in the UK. It has become apparent that my wheel studs - front and back are way too short. I took a sample (one from rear and one from the front) down to my local shop to order in and surpr..
10
2012/11/20 21:04:19
the_cheese

Cheap car batteries PERTH

Hi to all WA folks out there, just thought I'd share a lil gem I found in Osborne Park. Challenge Batteries - they import and brand batteries which are often found in a lot of other retail outlets for big $s. I bought a sealed 760CCA battery for my GQ Patrol at about $60 cheaper than the best pri..
1
2012/10/21 11:00:52
markrs

Garage/Workshop Floor - Perth Members

Hey Guys, Moving into a new house this month are are looking at getting the garage floor (55sqm) painted/sealed, it has never been done before. I will use my garage for general use as well as light mechanical work. Can anyone recommend a good company in Perth that does garage floor painting/sealing ..
1
2012/10/05 18:05:06
Escortr1x

Specialty tools

Anyone requiring specialty tools ie sockets for head bolts on 2 ltrs ... Specialized tooling in prospect helped me out awesomly 83449826 this is in Adelaide..
10
2012/09/15 11:48:23
ratta tat tat

Upgrade your jumper leads!

Hi. After trying to start my pinto out of the car it became apparent that the starter was not getting enough current from the battery. I decided to pull the rubber down from the alligators and discovered the '80A' jumper leads had about 2/10 copper and 8/10 insulation.... a bit like honey chicken!!..
2
2012/08/31 14:59:34
TC and RS

Car Storage Melbourne

Hi All, I've moved into a new factory in Heidelberg and have some space available for Classic/Race Car Storage. Must be known to me or have references from somebody I know. Fully secure with like minded enthusiasts. 24 hour swipe card access. Will have internet/smart phone CCTV. $220.00 per month. ..
2
2012/06/27 20:49:03
TEX

MK1 Escort Door removal

Well after beating the hell out of the last remaining door hinge pin, heating it, soaking it, bash, heat, soak, bash, for afew days, I finally gave up on the method and resorted to cutting! I used a cut down, fine pitch hacksaw blade and made it into a long thin wedge. And slowly cut, in very small..

2012/06/26 09:21:12
BrandonC

Tips Galore.

Just bored and thought id start up and threat and hope it is positive. Just post your best known tips. :) Doesnt HAVE to be Escort/car related. But yehh.. Hope people post. Brandon...
16
2012/06/25 17:23:46
ratta tat tat

Rear crank seal?

Is there any way to DIY the rear crank seal on a kent motor? The manual shows FORD specific tools to hammer it in. What can be used as a substitute? Should the seal be lubed before driving it in?..
1
2012/04/01 07:22:58

1 2 3 - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account