For Sale: Forged 3S bottom end parts

Re: For Sale: Forged 3S bottom end parts (robk)

Fri, 27 Apr 2018 13:19:37 GMT

The pistons and rods are now SOLD!

Re: For Sale: Forged 3S bottom end parts (Falcon)

Fri, 27 Apr 2018 13:07:08 GMT

PM sent regarding Pistons and rods.

Re: For Sale: Forged 3S bottom end parts (robk)

Fri, 27 Apr 2018 09:19:21 GMT

MG_MR2
Hey Rob, what's the condition of the sump? Particularly the sealing surfaces

I'm not sure, I'll have to check next time I drop by the engine builder.

Re: For Sale: Forged 3S bottom end parts (MG_MR2)

Thu, 26 Apr 2018 20:01:09 GMT

Hey Rob, what's the condition of the sump? Particularly the sealing surfaces

Re: For Sale: Forged 3S bottom end parts (Carmikey)

Thu, 26 Apr 2018 11:36:35 GMT

How about talking him into coming over to Wakefield Park in Oct, then it will be free pickup 😉

Sent from my SM-J320ZN using Tapatalk

Re: For Sale: Forged 3S bottom end parts (robk)

Wed, 25 Apr 2018 21:35:31 GMT

Sw2091
How much for just the piston and rods

Sent from my SM-G955F using Tapatalk

How about $400 including shipping?

Re: For Sale: Forged 3S bottom end parts (Sw2091)

Wed, 25 Apr 2018 21:16:13 GMT

How much for just the piston and rods

Sent from my SM-G955F using Tapatalk

Re: For Sale: Forged 3S bottom end parts (robk)

Wed, 25 Apr 2018 20:53:07 GMT

Now pistons 3 and 4 (3 photos of each, labelled a/b/c in the file names), and a few other photos:

Re: For Sale: Forged 3S bottom end parts (robk)

Wed, 25 Apr 2018 20:50:51 GMT

Also, I'm now adding some photos.

Firstly, pistons 1 and 2 (3 photos of each, labelled a/b/c in the file names):

Re: For Sale: Forged 3S bottom end parts (robk)

Wed, 25 Apr 2018 20:47:49 GMT

Sw2091
I'm interested how much to ship to adelaide

Sent from my SM-G955F using Tapatalk

Hi, would you just want the pistons and rods, or everything?
If I was going to ship the parts interstate, I'd prefer for it to just be the pistons and rods to make it easier.
If you really want everything, then I'll get a quote for you.

Re: For Sale: Forged 3S bottom end parts (Sw2091)

Wed, 25 Apr 2018 12:13:41 GMT

I'm interested how much to ship to adelaide

Sent from my SM-G955F using Tapatalk

Re: For Sale: Forged 3S bottom end parts (robk)

Wed, 18 Apr 2018 22:30:07 GMT

Crjfly
Hi, I’d be interested. Just got last years tax down.
I can’t DM yet as I just joined.

Nice! Where are you located?

Re: For Sale: Forged 3S bottom end parts (Crjfly)

Wed, 18 Apr 2018 18:55:11 GMT

Hi, I’d be interested. Just got last years tax down.
I can’t DM yet as I just joined.

Re: For Sale: Forged 3S bottom end parts (robk)

Tue, 17 Apr 2018 13:55:23 GMT

Bump.

For Sale: Forged 3S bottom end parts (robk)

Tue, 27 Mar 2018 15:19:10 GMT

Hey guys,
Now that I'm upgrading to a 5S bottom end, I need to sell some of my 3S stuff.

I have the following parts to sell (there's only ~20,000km on these parts since the original rebuild):
- Gen 2 3S-GTE block (cylinders bored to 86.5mm, like any typical 3S rebuild)
~~- Used CP forged pistons for 3S-GTE, part number SC7450 (86.5mm)~~ SOLD!
- 3S-GTE crank (already checked for straightness and given the OK)
~~- Used Eagle 3S-GTE rods~~ SOLD!
- Used 5S-FE main caps (from the 5S-FE engine that I bought for my new setup, which will have billet main caps instead)

The parts are straight out of my 386rwkw setup.
Since there's only ~20,000km on the pistons and rings, the intention would be to keep using the existing rings to avoid removing more material from the cylinder walls with another hone.

The 5S-FE main caps and the 3S-GTE block would need to be machined so they match up properly, and you would also need to source new main bearings.

I also have the following used parts which I could sell individually:
- Genuine Gen 2 3S-GTE water pump with only ~20,000km on it ($50 ONO)
- Genuine Gen 2 3S-GTE oil pump with only ~20,000km on it ($50 ONO)
- Gen 2 3S-GTE oil sump, with an AN fitting welded on for a return from the oil catch can. ($?)

Ideally the buyer would be in Sydney.
All of the parts are currently at Advance Motor Mechanics in South Strathfield, and I could meet there with a potential buyer if required.

If no one shows any interest in these parts, then I will get Advance Motor Mechanics to re-assemble them into a complete bottom end that I would then sell.