WTB: AW11 Ignition lock/barrel + key

Re: WTB: AW11 Ignition lock/barrel + key (feral4mr2)

Thu, 05 Mar 2015 23:02:27 GMT

nah the ones I have have play mate.

Re: WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Thu, 05 Mar 2015 22:44:24 GMT

feral4mr2
I have a lot of spare suspension components if your ever after some. if I knew you were after springs could of helped there...

best of luck

The springs should hopefully be on their way and I'm stopping by a shop tomorrow who said they could fix up some new bushings for the tie rods (not sure about the cost yet). But if you've got healthy tie rods that might still be interesting if the bushings ends ends up costing a fortune.

Re: WTB: AW11 Ignition lock/barrel + key (feral4mr2)

Thu, 05 Mar 2015 22:26:47 GMT

I have a lot of spare suspension components if your ever after some. if I knew you were after springs could of helped there...

best of luck

Re: WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Thu, 05 Mar 2015 17:32:47 GMT

Yeah they're great that way! Just wish the parts unique to it would be as easy to find. Still desperately looking for rear tie rods. Finally managed to source some front springs from NSW. Best option so far for tie rods are UK with expensive shipping and long wait. :(

Re: WTB: AW11 Ignition lock/barrel + key (feral4mr2)

Thu, 05 Mar 2015 17:30:14 GMT

glad you got it sorted. you would be amazed at what other Toyota models share the same bits n pieces..

I remember back in the 90's reading an article about the aw11 and they said that Toyota built it from their spare parts bins.. haha

Re: WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Sat, 28 Feb 2015 23:43:38 GMT

I went up to U-Pull-It to have a look at Toyotas up there. Seems like V20 Camrys have the same ignition lock so problem solved. :)

Re: WTB: AW11 Ignition lock/barrel + key (Carmikey)

Sat, 28 Feb 2015 14:01:34 GMT

Hi tim, i think i have one. Will check tonight.

Re: WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Sat, 28 Feb 2015 13:09:53 GMT

Removing it was a piece of cake. Now that I've got it loose it looks like mine is slightly different to the one I ordered. The pin that looks it in place is further back (as yours in the picture) than the one I ordered and any other I can find on ebay. That said though there is a mark in the cylinder where the barrel goes indicating an alternative position for that pin so I might be able to drill a new hole for it to fit in if it's identical apart from that.

Here's what mine looks like. Does anyone know where I could source one in Adelaide?

Re: WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Wed, 25 Feb 2015 23:44:53 GMT

Thanks, even that thing whole could be interesting if it comes to it. Since you've got it loose how fiddly would you say it seems to be to replace the barrel? Just curious as that's what I'll most likely try first.

Re: WTB: AW11 Ignition lock/barrel + key (feral4mr2)

Wed, 25 Feb 2015 23:25:32 GMT

i have this, would rather keep it whole though. if you get stuck, flick me an email. feral4mr2@hotmail.com

WTB: AW11 Ignition lock/barrel + key (xtimmyx)

Wed, 25 Feb 2015 19:49:19 GMT

I'm in desperate need of a replacement ignition lock and key for my -88 N/A AW11 to get it back on the road again. Toyota has stopped supplying them and couldn't even give me an part number anymore but said there's a few different varieties as well to make matter worse.

I've got one on it's way from Singapore claimed to be for the S/C but I wouldn't mind doubling up rather than wait a few weeks only to find out it doesn't fit.

So if anyone has one I'd be very happy to buy it off you for a reasonable sum.