Engines - Pinto

To Bottom

Engines - Pinto (p.16)
Post New Thread
Regular
Ionix

Idles perfect when cold, not when hot.....Pinto with EFI

Guys, Im thinking this is probably an ecu/tuning problem but i thought I may throw a few possibilities out there and see what i get back.... I have a worked pinto motor and head with lumpy cam. Im running EFI on a microtech fuel only ecu. The injectors are 205cc (admittedly a bit too big for this ..
14
2012/01/02 14:27:08
micka

+80 hp. How would you do it?

if its possible, how would you do it? Say the rules were no efi pinto based can it be done with NA or only FI? Secondly, how would you get that power to the ground? Cheers boys. Food for though :D..
28
2011/12/13 19:28:17
57bus

oil presure problem

hi there everybody, i have just been trying to start up my rebuilt pinto engine. i have been trying to prime the motor and get the oil presure up before firing it. but i cant seem to get any . i took the rocker cover off to see if there was any oil flow over the cam and there was nothing there eithe..
3
2011/12/12 22:21:31
mk1escort73

turbo pinto

turbo charged pinto's who has one? how good does it go?how reliable is it?is it costly to build?i have a mk1, any info would be sweet cheers..
15
2011/11/12 21:42:46
Wozzah

Pinto Build 1

Hi All, Doing a couple of Pinto engines for customers at the moment, thought I'd post a thread up on the builds. This one is for a tarmac rally car. The aim is to see 130rwkw, the most I have seen on the dyno I use in the past out of a Pinto is 128rwkw. At the moment it is a collection of parts. ..
30
2011/09/26 21:37:41
eamonlad

pinto adelaide

hi im looking at getting some work done on my engine,bottom end and head,where do people in adelaide go too get work done like this and not get ripped off cheers..
5
2011/09/04 15:48:32
Monaroman68

Camshaft selection to suit 2lt

Hey guys looking for advice on selecting a cam to suit my 2lt used for speedway racing. Engine is 30th over wiesco pistons long chromoly rods 5.7" zero deck height 12:1 comp head is group1 big valves(long) flowing 197cfm @28" has 45 twin webers running avgas , previous cam was crane billet small ba..
3
2011/09/03 12:21:38
micka

weber carb comparason

hey boys, is there anywhere or anyhow i can find out the differences between the weber codes? i had a 38dgas, and i think i want another one. but theres heaps of different ones!..
6
2011/08/28 09:50:36
wombat2509

fuel pump

Hi My fuel pump is leaking oil, can ay one tell me if they are easy to get and what do they cost. thanks John..
4
2011/07/28 07:56:13
MK2 Pete

WC X MEMBER + TYPE 9 = PROBLEM

HEY GUYS, I have just installed my worldcup x member and type 9 onto my Pinto powered MK2 escort. Problem = The tail of the box tops out on the roof on the gearbox tunnel (just near leaver) and I cant lower it as the front edge of sump is hard up and resting on the rear of the world cup x member...
2
2011/07/18 12:27:20

<< ..16 17 18 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account