Engines - Pinto

To Bottom

Engines - Pinto (p.10)
Post New Thread
Regular
ratta tat tat

Penrite HPR-30 + K&N HP-3001

So after a little research this combo looks good for preserving my pinto lump. Anyone else using these products? Thanks..
2
2013/12/01 23:57:26
ITFKSU

Turbo Cam

...so i just got off the phone to esslinger racing only to find out they stopped making solids for the 2.0.....got offered a 600 lift thing but was full hydraulic and total cost would set me back 2k...and cam would kick in at 5000 rpm. Feel Free to share knowledge and experience on suitable turbo ca..
6
2013/11/19 20:59:19
Aussie RS2000

i want more power

Hey guys, does anyone know how to go about putting a motorbike carby on 2L pinto?..
3
2013/11/19 09:42:44
Drewdog

Pinto engine wanted, perth...

Hello all,Looking for a pinto engine in perth, Escort or Cortina, complete engine to a block and crank.....Cash paid, can pickup any area......Cheers Drew........
1
2013/11/18 20:32:18
war

CAMSHAFT HELP .. made in usa what is it

I have a made in usa camshaft in my pinto A 29 C.2 I.5 CWC D.2 (in the casting) on the tail stamped 0ant help please...
1
2013/11/03 12:25:28
Robmk2

Camshaft ID help mk2 escort 2.0

Reading around I found that "Made In USA" is a stock pinto cam, ill get the dial gauge out and do some measuring, but can anyone confirm that this is a standard cam? https://lh4.googleusercontent.com/-TpK5FVNJtX0/UYywYC3mfkI/AAAAAAAAAOk/MByg-5qseMs/w868-h651-no/2013-05-10+16.54.07.jpghttps://lh6.go..
5
2013/10/18 19:38:52
Drewdog

Weber 44IDF advice please...

Getting to the engine side of my rebuild. The car had some sidedraughts, they taught me a lot but it's time for an old dog to learn a new trick.............Looking at 44IDF's, I can get the carbs, jets and filters ok and a repo manifold, I haven't looked to hard for an original yet. How hard will an..
12
2013/09/27 15:00:08
war

how to find out the compession ratio pinto 2L

how to find out what compression ratio you have, if you don't have the engine history.measure the head/or the block? if so how..
1
2013/09/06 11:46:04
laurie

Sierra Injected Pinto's

Im in the process of putting Sierra Injection on my pinto in my MK1. I know of a few guys on the forum who have done this. I have the Tear Drop Port Head and EEC-IV ECU plus Electronic Dizzy. Im going to get the head flowed and trace down a FR34 cam kit when I go to England later mid year. Any info ..
6
2013/08/06 19:42:53
davus

Problems cranking a freshly built motor - Confusing me!.

Hi All, So, for the last few weeks ive been pottering around in the garage rebuilding the engine for my project RS2000. Whilst I am by no means a mechanic, i believe I am relatively mechanically minded. I have rebuilt quite a number of motors before (albeit not for quite a number of years), and have..
7
2013/08/06 19:23:37

<< ..10 11 12 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account