Help... URGENT!

To Bottom

Help... URGENT! (p.41)
Post New Thread
Regular
Diablo69

Pre ignition or run on

Hello Does anyone know where to start looking to stop pre ignition or run on problem on a standard MK2 Pinto setup. Basically when the car is turned off the engine shutters and tries to keep running. This happens about 50 percent of the time but much more once at full temp. When cold it does not see..
5
2012/10/09 21:39:14
obsesscort

Fuel return line

Hey guys, Would the emissions tube (slightly smaller diameter than the supply tube) suffice for a fuel return on my 1.6 to 2.0L conversion? If not, where could I source that hard plastic fuel line?..
2
2012/10/09 20:04:15
rham243

Help with Classic Ford transmission

Restoring a 1949 Ford sedan with my dad. We have a 289 that we pulled from a 60's mustang and rebuilt to go into the 49'. We are trying to figure out what type of transmission to go with that will bolt up to the 289 and work with the existing 3spd column shifter. My dad wants to go with an automatic..
1
2012/10/08 17:48:08
Matt75

Tightening Up Shock absorber nut

Hi Guys, I got 1 of the front struts installed today and when I went to tighten up the top shock absorber but it tightened it up a bit but then it just spins the shock shaft. I have read that an impact driver is the way to go but I don't have one. You could grab the shaft with mutigrips, with someth..
2
2012/10/08 12:57:30
mattsmithadelaide

2L Pinto workshop manual

I have lost compression in two of my cylinders on my pinto. Desperately In need of a good manual to instruct on the rebuild of the motor. I cannot find any manuals unders $100. Just wondering if anyone knows of any links or cheapers alternatives? Something that covers step by step the rebuild of the..
3
2012/10/08 10:48:08
ratta tat tat

K&N filter assembly for pinto

Well the K&N website is a bit of a joke eh. Someone needs to sort out all the product codes, none of the codes match descriptions (dimensions, replacement filters etc). Repco can't find these part numbers and K&N australia has no idea about them either. Anyway! Can someone please tell me ..
10
2012/10/05 22:19:11
chumud

Capri hubs needed

Hey all I desperately need a pair of later model Capri hubs as my ones are for an early model. I need the ones with the later smaller outer bearing. Thanks for your help...

2012/10/05 17:06:34
obsesscort

weber 32/36 dgav

Hey guys, does anyone have a spare carb for the pinto they would part ways with for $? I've got mine on, but it seems theres a lot of stuff missing, having trouble getting the choke to work... seems like theres meant to be a spring that holds the flaps closed allowing for the pressure to suck them o..
8
2012/10/05 10:30:09
ESK-74

Mk1 Heater/Blower motor resistor

Hi Guys, My car is currently down at the auto elecy's getting wired up, and i got a phone call from him today asking for my fan resistor so i have 2speeds for my fan. They only thing is i thought he had everything he needed and i threw my old harness out on monday. So i can use an aftermarket ..
2
2012/10/04 19:52:56
Matt75

Someone with machining skills & equipment wanted to machine down strut top spacer

Hi Guys, I am just finishing off my front suspension I need to get the strut top spacer I have machined down 1mm (as per the pics) otherwise the shock will bounce around inside the stut tops. Even though it's only 1mm I want it done properly as if I attack it with the angle grinder I'm sure it won't..

2012/10/04 16:36:36

<< ..40 41 42 .. - Powered by APG vNext Trial

© 2026 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account