Help... URGENT!

To Bottom

Help... URGENT! (p.19)
Post New Thread
Regular
mudguts

Help me ID a cross flow motor

Can anyone help me Id this Motor it was in a mk11 cortina.has a stainless tag Left rear OE9c71 00680 welded over a casted number 871F 6015JLeft front is K15 Right front is JA right rear is FOMOCOIt has the Dip stick at the front left and the block is about 30mm high from water pump to headIm thinkin..

2014/06/29 17:13:36
Juiceman

Thread sizes!

Hello all! I have two thread sizes I'm trying to figure out, just for replacing nuts and stuff...all off a MK2 Escort. 1. Rear shock mount (lower)2. Front sway bar bracket (body mount) Matt75, I'm looking at you! You're normally the first to reply to my thread size questions. Thanks!..
5
2014/06/26 19:10:07
smallvan

printed circuit board repairs

Does anyone know where i can get, a new printed circuit for my speedo and fuel gauges.As mine has died,i did some temp repairs,but io have no gauge lights and the temp reads cold all the time...
1
2014/06/10 20:53:40
Jaycees

Help - answers needed Mk1 Escort

I have a Mk1 Escort Auto body which has had some butchery done to the tunnel."I am putting a 2lt manual in it"I have fitted and welded in a manual gear stick housing panelbutThe prior owner cut out the tunnel reinforcer so I took one out of a Mk2 body I chopped up and was saving it.I was just triall..
6
2014/06/09 20:45:46
ratta tat tat

Somethin's smokin

Does hi-temp paint for extractors have a life span? and does it burn once that time is up? I can see and smell smoke coming from the hot side of the engine bay but can't determine if it's the paint burning of the pipes or the fire foil I installed on the clutch cable 18 months ago http://i194.photob..
6
2014/05/30 23:24:26
viskoe

Can I use a 2L Master Cyl on a Mk1 Braking system?

Hi allCan I use a 2L Tandem master cylinder on my Mk1 and just bock off one port off the master cyclinder with a bleeder?Or doI have to feed each front disc with a seperate brake line and remove the brass T piece that feeds both front discs?I am using 2L discs and drums on my Mk1. ThanksEmil..
4
2014/05/21 12:07:12
yan_83

XF alternator on Escort Mk2

Hi All, Managed to find a Falcon XF alternator to replace the alternator on my Escort Mk2, the mounts on the replacment alternator do not line up with the mount attached to the engine block. Is there a trick to this or do i need XF mounts? Is there anything else i need to do to install correctly. Th..
7
2014/05/18 02:34:20
spanner

xflow starter motor

Hi all, Probably been asked before but how many teeth should there be on a 1600 711M xflow starter motor?burtons list both 9 and 10 for xflow. I only ask as I have the chance to buy a good second hand reduction starter.any help would be great ThanksTim..

2014/05/08 12:33:09
wade

Can't tune my pinto

Hey everyone. I seem to be having trouble tuning my pinto here is the specs it's a pinto with a 32/36 carb medium sized cam and a points-less dizzy and the whole motor is freshly built. It will start and run but won't idle unless the idle speed screw is wound all the way in. Also the idle mi..
6
2014/05/01 22:27:01
hoogs544

wanted - clutch release thrust bearing carrier V6 Capri

Hello all I have recently been able to find a replacement gearbox (after 13 months) for my MK1 V6 Capri In that time i have managed to loose the clutch release thrust bearing and the carrier that holds it to the clutch fork I now have a new bearing but not way to hold it to the clutch fork Does anyo..
1
2014/05/01 21:38:25

<< ..19 20 21 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account