Help... URGENT!

To Bottom

Help... URGENT! (p.14)
Post New Thread
Regular
Jaycees

Brake Pedal Issue

I could really do with some pro advise and guidance.I have a 1975 Mk1 Escort and really struggling to get a hi brake pedal but,The system has been bled several times - no air or air locksI have looked to see if I accidently fitted a mix system of booster and pedal arms rods but they are okWhen I put..
4
2015/06/21 19:04:31
wade

noisy tappets/ valve clearance

Is anyone able to tell me what i need to set my valve clearances to? I have set them to factory settings but its a re grind cam and they are quite noisy. All the specs on the card they gave me say running clearance inlet .008 exhaust .008 lift @ lobe inlet 264 ° exhaust 264° Advertised timing ex..
14
2015/05/25 17:09:30
ratta tat tat

Pinto Clutch info

Hi, I bought an HD clutch cover the same as this but it came with a solid (uncushioned) 4 paddle plate as seen below. Is the cover any good and will it work well with this type of clutch plate? The car will be making 130~140 RWHP and used mainly on the road for weekend drives. Will I be better wi..
6
2015/05/25 15:37:30
Escortracer96

PLEASE HELP!!! stalls when braking!!

My partners Mk2 Escort 1.6 Manual keeps wanting to stall when brakes are applied. Been searching and reading the manual for hours and cant seem to figure out what's wrong... Please help any advice would be amazing. only thing we can think of is maybe the fuel mixture or something wrong with the carb..
7
2015/05/23 22:01:07
gtv6capri

I need a Spray Painter / panel beater in Melbourne

Hi all Im looking for a spray painter panel beater in Melbourne, I need a basic job done on a car, all my usual guys are not taking on work. Its not a big dollar car so I dont want want a show stopping 2 pac candy harlequin, just a rub down a few corrections and a new caot of paint, something in vic..
1
2015/05/23 21:15:04
wade

temp sensor broken non ford related

Hi all my father in law just broke the temp sensor off in the head of his v8 ski boat. He got all the thread out but the sensor is floating in the head would this cause any overheating problems or would it be ok to leave it in there? Thanks in advance..
1
2015/05/23 10:33:12
ratta tat tat

Screeching noise with new xflow??

I have a thread in showroom (haydn's MK1) showing the progress of my 1.3 to 1.6 engine swap. So I got the motor installed a couple of nights back, spent the last day or so fitting the manifolds and hoses. Then I put in oil & water, cranked the motor with no plugs to get the oil pressure up. I shoul..
16
2015/04/08 21:17:03
camo91

megasquirt efi pinto escort

Who runs this ecu system... pm please!!!..
9
2015/04/05 20:24:28
MATTJ

lower control arm rose joint

Hi all i have bent the rose joint on one of my adjustable lower control arms in my rally car and was wondering if anyone knew what size & thread they are? id like to just buy another pair of the rose joint instead of another full set of control arms at this stage. CheersMatty..

2015/03/31 08:27:17
PeterM

Escort spark plugs fouling.

Hi All, My daily driver is my completely factory standard 1979 1600 Escort panel van.I drive it sedately mainly through residential streets at 50 to 60km/h, approximately 24km each day, 6 days per week.Over the past 2 to 3 years I have been finding that I need to clean an opaque (clearish white) col..
5
2015/03/17 01:16:47

<< ..13 14 15 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account