Help... URGENT!

To Bottom

Help... URGENT! (p.11)
Post New Thread
Regular
wade

38 dgas jetting for pinto

Can any body point me in the right direction on what I should be jetting my 38 dgas for my 2litre pinto? Googling tells me it should be Mains 145 Air jets 185 Idle jets 45 Acc pump 55 Emulsion tubes f50 Idle air bushes 145 I would much rather hear it from someone on here TIA Wade..
2
2016/02/12 17:36:55
Green machine

Escort 1976 mk2 Panel Van wipers

Hi, I'm doing up a Escort 1976 mk2 1.6 Panel Van which has the wiper arm missing. Can anyone tell me how to tell if your wiper setup is intermittent or not before i hunt down a replacement?..
2
2016/01/31 15:47:19
gmgeeman

MK1 Escort door glass???

Hi all, would anyone know where I could get some new door glass for a 2 dr MK1 in Australia. They were available a while back and can't remember where...
5
2016/01/22 02:11:10
Jason

Coilover Top Spring Seats Loose

Hi,Are the top spring seats / d-caps on coilovers meant to be loose without spring pressure on them?I've torqued down my adjustable strut tops properly but the top spring mount is still free to move maybe 5mm up & down on the shock rod. It obviously seats under the strut top with the weight of t..
5
2016/01/04 15:13:49
Flighter

Window regulator grease

Hi all, Can someone tell me what type of grease that creamy white stuff is that Ford used on window regulators and pedal bushes is? Thanks...
4
2016/01/03 21:07:36
Flighter

ARP Pinto flywheel bolt torque

Hi everyone. I'm installing some ARP flywheel bolts in my Pinto, and noticed that the recommended torque setting is noticeably higher than factory spec, i.e. ARP says 70 ft-lb to Ford's 50 ft-lb. Any reason to be suspicious of the higher rating stated by ARP? Thanks...
2
2016/01/03 16:26:00
mvscon

Fitting sunroof

Hi I'm about to refit sunroof in my escort ( I know not ideal but its how it came and its grown on me) When I removed it there was a gasket which I haven't been able to find or anything to replicate it. So I was going to fit with sikaflex . Has anyone an idea on whether that would be suitable or a..
3
2016/01/03 10:22:20
ratta tat tat

Pinto head bolts

I found these head bolts in a spare motor of mine. I noticed they're torx instead of spline. Are these aftermarket? Would they be stronger than the spline bolts? Thanks http://i194.photobucket.com/albums/z282/rattatattat07/20160102_111725_zpsripmurvl.jpg..
1
2016/01/02 20:56:01
Jason

Helper Spring Platforms too Long?

I'm about to fit the helper springs to my coilovers.It seems that the platforms supplied with the helper springs are too long & the helper spring can't fully compress.To me, that means the weight of the car will be riding on the collars of the plastic helper spring platforms, instead of transfer..
2
2016/01/01 22:50:50
Jason

Is this a Mk2 Escort Front Sway Bar?

Hi,If anyone has a Mk2 Escort front sway bar handy, could they confirm the measurement of 415mm from the long front section of the bar to the tip of the threads please? Like in the picture below.I know it looks like 435mm or so in the pic below, but that's just parallax error. . . this one is defini..
2
2015/12/25 01:25:42

<< ..10 11 12 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account