Induction (Carburettors / Fuel Injection)

To Bottom

Induction (Carburettors / Fuel Injection) (p.3)
Post New Thread
Regular
Ratbag

WATER INJECTION ... FOR NA ENGINES.!!!

Sorry, not all, i haven't proved how to, on Bike Carbs, (like the little steam engine, i think i can.!!) the setup used by many members, Hanrahan is one that may still be running that setup.!! ...However, WI does work and with many cars/engines running EFI now to not burn, just one exhaust valve, i ..

2016/04/03 21:40:22
Drewdog

Perthies: a tuner to avoid...

Hey Perthies, avoid BPT motorsport in Wangara. Had a hellish time with the prick this week.AVOID AT ALL COSTS.Cheers Drew.....
2
2016/02/06 18:39:25
RSman4ever

upside down itb's?

Hey guys, I was just checking out Retro Ford owner Dave Collage's duratec powered LADA! on speedhunters.com. He has mounted jenvey TB's upside down for cosmetic reasons, I really like this idea and was wondering what the down sides might be? Obviously adjusting things would be a pain but what about ..
1
2015/12/27 17:50:50
Drewdog

Electric fuel pump problems

G'day all,Having a few problems with an electric pump not pumping fuel. It tests ok on the bench. It's mounted as close to the tank and as low as I can get it, on the floor pan just past the spring hangers, if I remove the line to the regulator and put it lower than the pump it flows fuel, after tha..
4
2015/12/22 19:41:35
NQRS

Fuel filler hose

Hi All,Had to replace the fuel filler hose in the boot, the old one started leaking when filling up the other day. Messed around with local suppliers to get a piece of hose but no luck. Got busy with google and found some really expensive bits-$11 an inch.! had a think about what was on my XA falcon..
5
2015/12/14 07:19:52
NQRS

CFM ratings for webers

Hi All, General question- has anyone published/ listed CFM ratings for the various webers. Know there are variations with choke- venturi sizes. Reason for asking- recently changed my twin 45's for a Holley. Didn't honestly expect, when my brother brought it up for me from Bris, that it would be a 35..
4
2015/10/03 23:18:27
Drewdog

Fuel pump wiring

G'day all, just after ideas on where the best circuit/ accessory point to wire an electric fuel pump would be. Only needs power when the ignition is on and there will be a switch in there too...Cheers Drew.....
4
2015/10/02 21:02:56
Drewdog

44 idf's on pinto base jetting

Hello all,Could anyone give me an idea on the base jetting for 2 44idf carbs on a mild road/ group 1 style pinto? Just need a rough idea to get the car started it will be dyno'ed later....Cheers Drew.....
4
2015/09/29 16:28:37
retro666

Carb plumbing?

Hi, With the single barrel carb on a 1600 there is a vent? Outlet on the drivers side of the bowl, what is it supposed to connect to?..

2015/09/02 12:14:14
what?

pinto hesitating from 4700rpm upwards

Ok guys, i nearly have my mk1 2 door to a stage that i am happy with. Its on the road and driving at least. The car has a 2.0 built by the previous owner so i dont know cr or camshaft selection. I had a new set of twin 45 added and a dyno tune completed. I dont put much faith in dynos but apparentl..
15
2015/08/14 08:45:17

1 2 3 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account