Brakes

To Bottom

Brakes (p.9)
Post New Thread
Regular
Power_Quest

pedal box, setting bias

hey there, just wondering if anyone has any advice when setting up the balance bar for a pedal box, im running 0.75 for fronts, 0.7 for rears. brakes are vented wilwoods up front and drums on the rear( not for long)..
9
2012/09/13 21:38:17
evobda2

Firewall mounted bias pedal box

Just saw this whilst looking through the Motorsport-tools site for a few bits.. A firewall mounted bias pedal box. Not a bad idea but im still not sure how it would sit on an escort as the usual brake booster mounts quiet low on the firewall so it might slightly defeat the purpose..? Would be good i..
1
2012/09/05 12:04:02
MK2 Pete

mk2 ESCORT - FLOOR MOUNTED PEDAL BOX

anybody fitted one off these floor mounted pedal box's, or know anyone who has? http://i110.photobucket.com/albums/n117/peterharper/15177EscortPedalbox.jpg..
3
2012/09/04 10:44:16
mattsmithadelaide

MK1 RS1600 Rear brake assemblys

Hi all, sorry for the rush of questions lately! I purchased a mk2 1976 escort which has a mk1 borg warner diff inside. The brakes are off a twin cam rs 1600. I was given a bag of 'bits' from the previous owner of which I cannot seem to find a logical position for the springs which I thought would b..
7
2012/09/02 18:59:17
Flighter

M/C to Booster gasket (Escort MkII)

I had my master cylinder overhauled, but the brake place couldn't supply a new rubber gasket that sits between it and the booster. I had a scrounge around a hardware store but didn't find anything suitable. Anybody know where to find one? They have an internal diameter of about 40mm, and I'm guessin..
5
2012/08/19 10:55:30
Matt75

Aeroflow Brake Lines

Hi Guys, My next step is to replace the front brake lines with braided lines. As I am also installing the Volvo calipers I want the lines to be longer so I can bolt them straight onto the calipers as per the pic. (Cheers to RS2000). My question is do I have to get a set of ADR Brake lines at over $2..
3
2012/08/13 08:20:11
Andrew

Wilwood and ADR compliance??

Can a boosterless setup with Wilwood fronts and R31 rears be made road legal in WA? Obviously would need dust seals (which is midlite I think)? Or is there a better caliper available for the front (that must fit under a 13" rim)? Can anyone recommend a good engineer in WA to go and see? There are a ..
4
2012/08/07 21:07:08
Matt75

Bleeding Brakes & M/C

Hi Guys, I just finished installing my Datsun 120y M/C in the eskie and now I need to bleed the system obviously. My question is that I have since found out I should have bench bled the M/C before installation to ensure there is no air in it. My question is, can i just bench bleed in in situ as it h..
6
2012/08/07 17:46:38
eamonlad

union size

Hey, does anyone no the union nut size for the dutsun 120y brake master cylinder witch im running on my mk1 escort, also witch pot is the front and witch is the rear. thanks..
7
2012/07/26 19:53:23
Matt75

Solid Brake Lines - What's the best material to use?

Hi Guys, I am redoing the brake lines in the engine bay and I am looking at all the different types of metal brake lines available and want to know what's the best omes to use? I have heard that stainless lines don't seal properly??? Any input is appreciated. Cheers Matt..
3
2012/07/17 21:10:53

<< ..7 8 9 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account